NE-500 OEM Application Syringe Pump |
|
Model: NE-500
|
Price: US $495 |
| |
Part ID: PUMP-NE500 |
|
NE-500 + OEM-Starter
|
Price: US $520 |
| |
Part ID: PUMP-NE500-STARTER-U |
- Computer controllable: networkable up to 100 pumps
- Stand-alone operation: pre-program the pump with a dispensing program, then operate the pump from an attached Foot Switch, button, or I/O controller
- Add the OEM Starter Kit to run as a fully functional, stand-alone pump
|
Description:
|
 | Open chassis design easily mounts into your system |
|
Features:
- Built for Automation
- Operates from a computer
- Infusion and withdrawal
- Set a single pumping rate and/or dispensing volume
- Program up to 41 pumping phases that change pumping rates, set dispensing volumes, insert pauses, control and respond to external signals, sound the buzzer
- Network, control, and monitor up to 100 pumps with one computer
- Motor stall detection available in NE-501 model ($550)
- Dispensing accuracy of ± 1%
- Unlimited lifetime technical support
- Two year warranty
Example Flow Rates (NE-500): |
|
Syringe Size (cc) |
Maximum Rate (mL/hr) |
Minimum Rate (µL/hr) |
| 0.5 µL |
25.49 |
0.001 |
| 1 |
53.09 |
0.73 |
| 3 |
192.5 |
2.646 |
| 5 |
406.1 |
5.581 |
| 10 |
600 |
8.244 |
| 20 |
975.8 |
13.41 |
| 30 |
1282 |
17.63 |
| 60 |
2120 |
29.13 |
|
Need higher flow rates?
Give us a call, we have other models available |
Sample syringe configurations, can hold any size syringes below 60 cc.
|
|
Maximum syringe size: Although a maximum of a 60 cc syringe is specified, the pump can hold up to a 140 cc syringe but can only open up to about 120 cc lengthwise
High pressure notes:
The NE-500 produces about 15 lbs of linear force at top speed and about 35 lbs at slow speeds. 10 ml/hr is an example of slow speed. The pressure that can be generated is relative to the syringe size. On a 60 ml syringe, this would roughtly produce about 30 psi
The high pressure version, NE-510, will approximately double the pumping force at the same speeds.
|
NE-510 High pressure variant (motor upgrade)
|
Model: NE-510
|
Price: US $535 |
|
Part ID: PUMP-NE510 |
Example Flow Rates (NE-510):
|
|
| Syringe Size (cc) |
Maximum Rate (mL/hr) |
Minimum Rate (µL/hr) |
| 0.5 µL |
91.83 |
0.001 |
| 1 |
191.2 |
1.459 |
| 3 |
693.4 |
5.291 |
| 5 |
1462 |
11.17 |
| 10 |
2160 |
16.49 |
| 20 |
3514 |
26.82 |
| 30 |
4619 |
35.25 |
| 60 |
7635 |
58.26 |
|
Need higher flow rates?
Give us a call, we have other models available
|
Sample syringe configurations, can hold any size syringes below 60 cc.
Note: The NE-510 model uses a 12V 1000 mA (full load) 2.5 mm center positive barrel power source
|
| |
|
|
| The NE-501 includes an optical encoder on the NE-500 that will detect and stop the the motor during a stall. Typically used in high pressure applications where there is a risk of exceeding the maximum force specified. Without the optical encoder, the pump will continue to cog the event of a stall. |
|
Model: NE-501 |
Price: US $550 |
|
Part ID: PUMP-NE501 |
|
|
|
|
Description:
|
Part ID: OEM-STARTER
|
Price: US $25 |
|
|
|
|
Description:
- Start, stop, or trigger the next phase on your syringe pump
- Attach to an NE-500 to allow stand-alone operation
- Utilizes the TTL logic port on syringe pump
- Quick and simple setup
|
Model: ADPT-2
|
Price: US $45 |
|
|
*** Not for clinical use on humans *** |
|